CVE-2021-45420
Emerson Dixell XWEB-500 products are affected by arbitrary file write vulnerability in /cgi-bin/logo_extra_upload.cgi, /cgi-bin/cal_save.cgi
CVSS
9.8
Critical
EPSS
17.5%
p97
KEV
—
Exploit Today
29
0-100
Published: Feb 14, 2022 · Last modified: Jul 9, 2026 · CWE-200 · CWE-306 · CWE-668
17.5%EPSS · 30 days17.5%
2026-09-262026-10-23
Emerson Dixell XWEB-500 products are affected by arbitrary file write vulnerability in /cgi-bin/logo_extra_upload.cgi, /cgi-bin/cal_save.cgi, and /cgi-bin/lo_utils.cgi. An attacker will be able to write any file on the target system without any kind of authentication mechanism, and this can lead to denial of service and potentially remote code execution. Note: the product has not been supported since 2018 and should be removed or replaced.
CVECVSSEPSSKEVRExploitTitleMod.
CVE-2026-1134925.3 MED—
——0The GeoDirectory WordPress plugin before 2.8.194 does not perform status, ownership or password checks when loading listings for one of its unauthenticated AJAX handlers, allowing unauthenticated users to disclose the content of non-public (draft, pending and private) listings by supplying their IDs.9hCVE-2026-1134905.3 MED—
——0The GeoDirectory WordPress plugin before 2.8.194 does not perform any status or ownership check when rendering a listing's map-popup through one of its single-item REST routes, allowing unauthenticated users to read the title, permalink and card fields of non-public (draft, pending, private and trashed) listings by supplying the listing ID.9hCVE-2026-799778.2 HIG—
——0The WireGuard VPN service in subsys/net/lib/wireguard/wg.c updated the peer endpoint from a message it could not authenticate. In handle_transport_data(), when the 32-bit receiver index of an incoming transport-data message matched no session, the code both scheduled a new handshake and copied the datagram's source address into peer->endpoint with memcpy(&peer->endpoint, peer_addr, sizeof(peer->endpoint)). Because the receiver index is unknown, there is no key with which such a message could be verified, so the address written into peer->endpoint is entirely attacker-supplied. Every other endpoint update in the implementation happens only after authentication — after the Noise handshake in handle_handshake_init(), or after AEAD decryption plus the anti-replay check in wg_process_data_message().
The WireGuard listener is registered with net_udp_register() using no remote address or port filter and defaults to UDP port 51820 (CONFIG_WIREGUARD_PORT), and wg_ctrl_recv() resolves the peer by interface rather than by any cryptographic identity. Any host able to send a UDP datagram to that port can therefore reach the defect off-path, with no need to observe legitimate traffic: a 16-byte datagram carrying the transport-data type, zeroed reserved bytes and an arbitrary receiver index is sufficient. The vulnerable branch runs whenever the peer has neither a valid handshake nor a current keypair — the state at boot and after a session expires.
A single spoofed datagram redirects peer->endpoint to an address of the attacker's choosing, and all subsequent handshake initiations, keepalives and encrypted data packets are sent there. The legitimate peer never receives the initiations and so never re-authenticates, and nothing resets the endpoint afterwards, leaving the tunnel persistently unusable on devices whose peer does not initiate handshakes itself. The attacker can also relay the redirected initiations to the real peer to place itself in the path of the tunnel, observing ciphertext and traffic metadata and selectively dropping packets. WireGuard's end-to-end cryptography still prevents decryption or forgery of tunnel content, so the impact is loss of availability plus limited confidentiality, not key compromise.
The fix removes the endpoint learning from this path entirely: the stale-session recovery is kept, but the handshake is sent only to an endpoint learnt from an authenticated message, falling back to the configured cfg_endpoint, and the message is dropped when neither is known. CONFIG_WIREGUARD is marked experimental and is not enabled by default.1dCVE-2026-554636.5 MED—
——0The Goobi viewer is a web application that allows digitised material to be displayed in a web browser. From version 4.11.0 to before version 26.05, several Jakarta WebSocket endpoints in goobi-viewer-core (DownloadTaskEndpoint, CampaignEndpoint, AutocompleteEndpoint, UserEndpoint) accept connections without verifying that the associated HttpSession belongs to a logged-in user, and none validate the Origin header against an allowlist. An unauthenticated attacker can therefore connect to these endpoints; through CampaignEndpoint this allows polluting the in-process crowdsourcing page-lock map and broadcasting forged lock messages, disrupting reviewers' work. This issue has been patched in version 26.05.1dCVE-2026-466519.8 CRI—
——0The Goobi viewer is a web application that allows digitised material to be displayed in a web browser. From version 24.03 to before version 26.05, the DownloadTaskEndpoint WebSocket endpoint (/tasks/download/monitor.socket) in goobi-viewer-core accepts download requests from unauthenticated users. This issue has been patched in version 26.05.1dCVE-2026-572075.9 MED—
——0NetBox MCP Server is a simple read-only Model Context Protocol server for NetBox. Prior to version 1.2.1, when running with TRANSPORT=http, the MCP server has no authentication on the HTTP endpoint. Any client that can reach the port gets a valid MCP session and full access to all four NetBox tools - no token or credential needed. This issue has been patched in version 1.2.1.1d