CVE WatchOct 19, 2026

CVE-2024-14040

In the Linux kernel, the following vulnerability has been resolved: net: nexthop: Increase weight to u16 In CLOS networks, as link failure

CVSS

7.8

High

EPSS

0.1%

KEV

—

Exploit Today

0-100

Published: Jul 26, 2026 · Last modified: Oct 19, 2026 · CWE-787

EPSS · 30d

0.1%EPSS · 30 days0.1%

2026-09-262026-10-23

Technical description

In the Linux kernel, the following vulnerability has been resolved: net: nexthop: Increase weight to u16 In CLOS networks, as link failures occur at various points in the network, ECMP weights of the involved nodes are adjusted to compensate. With high fan-out of the involved nodes, and overall high number of nodes, a (non-)ECMP weight ratio that we would like to configure does not fit into 8 bits. Instead of, say, 255:254, we might like to configure something like 1000:999. For these deployments, the 8-bit weight may not be enough. To that end, in this patch increase the next hop weight from u8 to u16. Increasing the width of an integral type can be tricky, because while the code still compiles, the types may not check out anymore, and numerical errors come up. To prevent this, the conversion was done in two steps. First the type was changed from u8 to a single-member structure, which invalidated all uses of the field. This allowed going through them one by one and audit for type correctness. Then the structure was replaced with a vanilla u16 again. This should ensure that no place was missed. The UAPI for configuring nexthop group members is that an attribute NHA_GROUP carries an array of struct nexthop_grp entries: struct nexthop_grp { __u32 id; /* nexthop id - must exist */ __u8 weight; /* weight of this nexthop */ __u8 resvd1; __u16 resvd2; }; The field resvd1 is currently validated and required to be zero. We can lift this requirement and carry high-order bits of the weight in the reserved field: struct nexthop_grp { __u32 id; /* nexthop id - must exist */ __u8 weight; /* weight of this nexthop */ __u8 weight_high; __u16 resvd2; }; Keeping the fields split this way was chosen in case an existing userspace makes assumptions about the width of the weight field, and to sidestep any endianness issues. The weight field is currently encoded as the weight value minus one, because weight of 0 is invalid. This same trick is impossible for the new weight_high field, because zero must mean actual zero. With this in place: - Old userspace is guaranteed to carry weight_high of 0, therefore configuring 8-bit weights as appropriate. When dumping nexthops with 16-bit weight, it would only show the lower 8 bits. But configuring such nexthops implies existence of userspace aware of the extension in the first place. - New userspace talking to an old kernel will work as long as it only attempts to configure 8-bit weights, where the high-order bits are zero. Old kernel will bounce attempts at configuring >8-bit weights. Renaming reserved fields as they are allocated for some purpose is commonly done in Linux. Whoever touches a reserved field is doing so at their own risk. nexthop_grp::resvd1 in particular is currently used by at least strace, however they carry an own copy of UAPI headers, and the conversion should be trivial. A helper is provided for decoding the weight out of the two fields. Forcing a conversion seems preferable to bending backwards and introducing anonymous unions or whatever.

Official references

git.kernel.orghttps://git.kernel.org/stable/c/b72a6a7ab9573e06d5c2fcb92eaa28614a735bfd

Related CVEs

CVECVSSEPSSKEVRExploitTitleMod.

CVE-2026-799828.8 HIG

—

——0The Bluetooth HCI USB transport class of the new USB device stack, subsys/usb/device_next/class/bt_hci.c, copies every controller-to-host HCI packet into a USB transfer buffer before enqueuing it on an endpoint. bt_hci_tx_sync_in() allocated that buffer from bt_hci_ep_pool, a fixed pool whose slots are only USBD_MAX_BULK_MPS bytes (64 on full-speed-only builds), and then performed net_buf_add_mem(buf, bt_buf->data, bt_buf->len) with no length check. HCI event and ACL buffers are sized by CONFIG_BT_BUF_EVT_RX_SIZE and CONFIG_BT_BUF_ACL_RX_SIZE and can be far larger, so the copy runs past the end of the 64-byte slot into the adjacent slots and into whatever follows the statically allocated pool. The device runs the local Bluetooth controller in raw HCI mode (CONFIG_BT_HCI_RAW), so the oversized packets originate over the air. With the HCI buffer sizes recommended for full-featured controllers, an unauthenticated attacker within Bluetooth range can supply the overflowing bytes: a connected peer that negotiates Data Length Extension can send ACL fragments up to CONFIG_BT_CTLR_DATA_LENGTH_MAX bytes, and an attacker that merely broadcasts extended advertising data reaches the same path through LE Extended Advertising Report events, which the controller fragments only to CONFIG_BT_BUF_EVT_RX_SIZE. In the stock configuration the overflow is already reached without any radio traffic: the mandatory Read Supported Commands command-complete event is 70 bytes and overruns the 64-byte slot by six bytes on every host initialization. Because net_buf_add_mem() validates tailroom only through an assertion unless CONFIG_NET_BUF_HARDENING is enabled, builds with CONFIG_ASSERT=n — the usual production setting — silently corrupt memory adjacent to the USB buffer pool with attacker-chosen contents, which on a target without memory protection between subsystems can lead to arbitrary code execution. Builds with assertions enabled fail the assertion instead and panic, giving a remotely triggerable denial of service. The fix introduces a separate bt_hci_tx_pool sized to MAX(BT_BUF_ACL_RX_SIZE, BT_BUF_EVT_RX_SIZE) for the controller-to-host direction while leaving the host-to-device pool at the endpoint packet size, which is already bounds-checked during reassembly.1d CVE-2026-799783.6 LOW

—

——0The RTIO streaming completion callback adxl345_process_fifo_samples_cb() in drivers/sensor/adi/adxl345/adxl345_stream.c clamps the amount of FIFO data it will report (read_len = MIN(fifo_bytes, buf_avail)) to the space actually returned by rtio_sqe_rx_buf(), but then queues one 6-byte bus read per hardware FIFO entry at consecutive offsets from read_buf, bounded by the device-reported entry count rather than by the clamp. When the allocated buffer is smaller than a full batch, the driver writes up to 186 bytes past the end of the allocation; a companion defect left data->fifo_total_bytes un-reset at batch start, so an aborted or errored chain could leave a stale write offset that pushes the next batch's writes out of bounds as well. A short buffer is an expected, first-class outcome of the RTIO allocator: rtio_block_pool_alloc() walks the requested size down one block at a time until a contiguous run is available, and the driver only demands sizeof(struct adxl345_fifo_data) + 6 bytes as its minimum. Any streaming configuration whose mempool block granularity is smaller than a full FIFO batch (204 bytes) — for example the sensor shell's RTIO_DEFINE_WITH_MEMPOOL(sensor_read_rtio, 8, 8, 32, 64, 4) used by sensor stream <dev> on fifo_wm incl, or the 16-byte-block streaming example in the documentation — takes this path whenever the pool is fragmented or the consuming thread falls behind. The out-of-bounds writes are performed by the I2C/SPI RTIO backend (DMA on many SoCs) into the shared RTIO block pool, corrupting neighbouring live buffers or, for a pool smaller than one batch, memory beyond the pool itself. The written bytes are accelerometer samples and the destination follows the allocation, so there is no controllable corruption primitive: the realistic impact is silent corruption of other RTIO consumers' data or a crash. Reaching it requires a board with an interrupt-wired ADXL345 built with CONFIG_ADXL345_STREAM, plus buffer-pool starvation, which a co-resident local workload can induce but which also occurs spontaneously under load; there is no network, USB or radio path to this code.1d CVE-2026-1157237.4 HIG

—

——0Snap7 through 1.4.3 contains an out-of-bounds write vulnerability in the passive partner that allows a malicious active partner to overflow application buffers by declaring an unvalidated BSend total length. Attackers connecting from the configured peer address can declare up to 65535 bytes and send a short fragment, causing BRecv to memcpy past the buffer and crash or corrupt SCADA, HMI or gateway processes.1d CVE-2026-1155047.8 HIG

2.7%

——1CFITSIO through 4.7.0 contains an out-of-bounds write vulnerability in ffgcls2() in getcols.c that trusts attacker-controlled heap descriptor lengths for variable-length string columns. Attackers can supply a crafted FITS file that overflows a fixed 28,800-byte stack buffer and the caller's string array, enabling arbitrary code execution.1d CVE-2026-1153933.8 LOW

0.5%

——0Wasmtime before 24.0.12, 25.0.0 before 36.0.13, 37.0.0 before 46.0.2, and 47.0.0 before 47.0.3 contains a type confusion vulnerability because several Store APIs fail to validate that objects belong to the Store's Engine. Embedders mixing objects between Engines via Instance::new, StructRefPre::new, or Tag::new can trigger trampoline signature mismatches causing out-of-bounds stack writes, GC heap corruption, or panics.2d CVE-2026-111497—

40.5%

——12A buffer overflow vulnerability in the Brotli decoder (c/dec/decode.c) in Google Brotli versions 1.0.3 through 1.2.0 on all platforms allows a remote unauthenticated attacker to corrupt adjacent decoder state memory, disclose sensitive memory contents, cause a denial of service, or potentially execute arbitrary code using a crafted Brotli-compressed stream. Users need to update any Brotli libraries or binaries between 1.0.3 through 1.2.0 to the latest available version: 1.0.10 or 1.1.1 or 1.2.1.7h