CVE WatchJul 24, 2026

CVE-2026-23467

In the Linux kernel, the following vulnerability has been resolved: drm/i915/dmc: Fix an unlikely NULL pointer deference at probe intel_dm

CVSS

5.5

Medium

EPSS

0.1%

KEV

—

Exploit Today

0-100

Published: Apr 3, 2026 · Last modified: Jul 24, 2026 · CWE-476

EPSS · 30d

0.1%EPSS · 30 days0.1%

2026-09-262026-10-25

Technical description

In the Linux kernel, the following vulnerability has been resolved: drm/i915/dmc: Fix an unlikely NULL pointer deference at probe intel_dmc_update_dc6_allowed_count() oopses when DMC hasn't been initialized, and dmc is thus NULL. That would be the case when the call path is intel_power_domains_init_hw() -> {skl,bxt,icl}_display_core_init() -> gen9_set_dc_state() -> intel_dmc_update_dc6_allowed_count(), as intel_power_domains_init_hw() is called *before* intel_dmc_init(). However, gen9_set_dc_state() calls intel_dmc_update_dc6_allowed_count() conditionally, depending on the current and target DC states. At probe, the target is disabled, but if DC6 is enabled, the function is called, and an oops follows. Apparently it's quite unlikely that DC6 is enabled at probe, as we haven't seen this failure mode before. It is also strange to have DC6 enabled at boot, since that would require the DMC firmware (loaded by BIOS); the BIOS loading the DMC firmware and the driver stopping / reprogramming the firmware is a poorly specified sequence and as such unlikely an intentional BIOS behaviour. It's more likely that BIOS is leaving an unintentionally enabled DC6 HW state behind (without actually loading the required DMC firmware for this). The tracking of the DC6 allowed counter only works if starting / stopping the counter depends on the _SW_ DC6 state vs. the current _HW_ DC6 state (since stopping the counter requires the DC5 counter captured when the counter was started). Thus, using the HW DC6 state is incorrect and it also leads to the above oops. Fix both issues by using the SW DC6 state for the tracking. This is v2 of the fix originally sent by Jani, updated based on the first Link: discussion below. (cherry picked from commit 2344b93af8eb5da5d496b4e0529d35f0f559eaf0)

Official references

Related CVEs

CVECVSSEPSSKEVRExploitTitleMod.

CVE-2026-1104917.5 HIG

44.2%

——13The ONVIF service on the E3 can be rendered unresponsive by sending malformed or incomplete requests to certain operations. The affected service stops accepting new connections while the rest of the device continues operating normally, and will recover automatically after a period. This can be triggered repeatedly by any unauthenticated party with network access to the device.2d CVE-2026-1123815.9 MED

28.4%

——9Apache Traffic Server can crash with a null pointer dereference when a client POST request is torn down via half-close while a chunked origin response is being reparsed from a reentrant write-ready callback, a timing-dependent race introduced by the CVE-2021-32564 flow-control backports. This issue affects Apache Traffic Server: 9.2.15, 10.1.4, 10.2.0. Users are recommended to upgrade to version 9.2.16, 10.1.5, or 10.2.1, which fix the issue.2d CVE-2026-799767.1 HIG

17.1%

——5The MCTP-over-I2C+GPIO target binding in subsys/pmci/mctp/mctp_i2c_gpio_target.c emulates a small pseudo-register file, where the bus controller first writes a register number and then writes or reads payload bytes. The selected register (b->reg_addr) and the data-phase flag (b->rxtx) were never cleared when the controller issued an I2C STOP, so after a completed transfer the target still had a data register selected while the packet buffer that register refers to had already been consumed and set to NULL by mctp_i2c_gpio_target_stop(). A controller on the bus can re-enter the same branch of mctp_i2c_gpio_target_stop() with a NULL buffer using two ordinary transactions and no authentication: first a normal packet write to MCTP_I2C_GPIO_RX_MSG_ADDR followed by STOP (which delivers and frees b->rx_pkt), then a bare read transaction followed by STOP. The failing read_requested() call leaves the stale state untouched and the I2C driver still delivers the STOP callback, which then calls mctp_bus_rx() with a NULL packet. The symmetric case exists on the transmit side, where the stale MCTP_I2C_GPIO_TX_MSG_ADDR selection dereferences b->tx_pkt->end after b->tx_pkt has been cleared and additionally signals b->tx_complete a second time, causing the next outbound packet to be dropped. The dereference happens in the I2C target interrupt handler, so on any target that traps accesses to address 0 the result is a fatal exception and a device reset or halt — a denial of service inflicted by any device able to act as controller on the shared management bus (for example compromised firmware on a peer MCTP endpoint or on the BMC). On parts where address 0 is readable, the impact degrades to a malformed packet buffer being handed to the MCTP stack and lost transmit packets. No attacker-controlled value is written and no confidentiality or integrity boundary is crossed. The fix resets b->reg_addr to MCTP_I2C_GPIO_INVALID_ADDR and clears b->rxtx at every STOP, so a new register must be selected before any data phase can run again. Only builds that opt into the experimental CONFIG_MCTP subsystem with CONFIG_MCTP_I2C_GPIO_TARGET=y are affected.2d CVE-2026-764927.5 HIG

29.4%

——9As part of Cisco's ongoing commitment to proactive security and product quality, the Cisco Expressway Series software engineering team has conducted a comprehensive internal security review. This review resulted in software hardening releases that address multiple internally discovered vulnerabilities.   The vulnerabilities tracked by CVE-2026-76492 are related to issues concerning null pointers that are grouped under the Common Weakness Enumeration (CWE) Base CWE-476.3d CVE-2026-202215.8 MED

47.3%

——14Multiple Cisco products are affected by a vulnerability in the generic routing encapsulation (GRE) tunnel decapsulation feature of the Snort 3 Detection Engine that could allow an unauthenticated, remote attacker to cause an unexpected restart of the Snort 3 Detection Engine. This vulnerability is due to improper handling of nested GRE traffic. An attacker could exploit this vulnerability by sending a crafted GRE payload through an affected device. A successful exploit could allow the attacker to trigger an unexpected reload of the Snort 3 Detection Engine, resulting in either a bypass or denial of service (DoS) condition, depending on device configuration. For more information, see the section of this advisory. The Snort 3 Detection Engine will restart automatically. No manual intervention is required.3d CVE-2026-968887.5 HIG

39.7%

——12A BIND resolver that is configured with both a "redirect" zone and "qname-minimization strict" may abort with an assertion failure while processing the redirect. This issue affects BIND 9 versions 9.16.0 through 9.18.50, 9.20.0 through 9.20.29, 9.21.0 through 9.21.26, 9.16.8-S1 through 9.18.50-S1, and 9.20.9-S1 through 9.20.29-S1.4d