CVE-2026-109371
ZITADEL 3.0.0 before 4.18.0 contains a missing authentication vulnerability in the hosted Login V1 UI, where the change-username handler act
CVSS
8.2
Alto
EPSS
0.4%
p29
KEV
—
Exploit Today
9
0-100
Publicado: 12 oct 2026 · Última mod.: 15 oct 2026 · CWE-306
0.4%EPSS · 30 días0.4%
2026-10-132026-10-23
ZITADEL 3.0.0 before 4.18.0 contains a missing authentication vulnerability in the hosted Login V1 UI, where the change-username handler acts on the account bound to a login flow before any factor is verified. Unauthenticated attackers can submit a victim's login name and then post a new username to rename any active human user, including administrators, locking them out.
CVECVSSEPSSKEVRExplotTítuloVis.
CVE-2026-799778.2 ALT—
———The WireGuard VPN service in subsys/net/lib/wireguard/wg.c updated the peer endpoint from a message it could not authenticate. In handle_transport_data(), when the 32-bit receiver index of an incoming transport-data message matched no session, the code both scheduled a new handshake and copied the datagram's source address into peer->endpoint with memcpy(&peer->endpoint, peer_addr, sizeof(peer->endpoint)). Because the receiver index is unknown, there is no key with which such a message could be verified, so the address written into peer->endpoint is entirely attacker-supplied. Every other endpoint update in the implementation happens only after authentication — after the Noise handshake in handle_handshake_init(), or after AEAD decryption plus the anti-replay check in wg_process_data_message().
The WireGuard listener is registered with net_udp_register() using no remote address or port filter and defaults to UDP port 51820 (CONFIG_WIREGUARD_PORT), and wg_ctrl_recv() resolves the peer by interface rather than by any cryptographic identity. Any host able to send a UDP datagram to that port can therefore reach the defect off-path, with no need to observe legitimate traffic: a 16-byte datagram carrying the transport-data type, zeroed reserved bytes and an arbitrary receiver index is sufficient. The vulnerable branch runs whenever the peer has neither a valid handshake nor a current keypair — the state at boot and after a session expires.
A single spoofed datagram redirects peer->endpoint to an address of the attacker's choosing, and all subsequent handshake initiations, keepalives and encrypted data packets are sent there. The legitimate peer never receives the initiations and so never re-authenticates, and nothing resets the endpoint afterwards, leaving the tunnel persistently unusable on devices whose peer does not initiate handshakes itself. The attacker can also relay the redirected initiations to the real peer to place itself in the path of the tunnel, observing ciphertext and traffic metadata and selectively dropping packets. WireGuard's end-to-end cryptography still prevents decryption or forgery of tunnel content, so the impact is loss of availability plus limited confidentiality, not key compromise.
The fix removes the endpoint learning from this path entirely: the stale-session recovery is kept, but the handshake is sent only to an endpoint learnt from an authenticated message, falling back to the configured cfg_endpoint, and the message is dropped when neither is known. CONFIG_WIREGUARD is marked experimental and is not enabled by default.10hCVE-2026-554636.5 MED—
———The Goobi viewer is a web application that allows digitised material to be displayed in a web browser. From version 4.11.0 to before version 26.05, several Jakarta WebSocket endpoints in goobi-viewer-core (DownloadTaskEndpoint, CampaignEndpoint, AutocompleteEndpoint, UserEndpoint) accept connections without verifying that the associated HttpSession belongs to a logged-in user, and none validate the Origin header against an allowlist. An unauthenticated attacker can therefore connect to these endpoints; through CampaignEndpoint this allows polluting the in-process crowdsourcing page-lock map and broadcasting forged lock messages, disrupting reviewers' work. This issue has been patched in version 26.05.14hCVE-2026-466519.8 CRÍ—
———The Goobi viewer is a web application that allows digitised material to be displayed in a web browser. From version 24.03 to before version 26.05, the DownloadTaskEndpoint WebSocket endpoint (/tasks/download/monitor.socket) in goobi-viewer-core accepts download requests from unauthenticated users. This issue has been patched in version 26.05.14hCVE-2026-572075.9 MED—
———NetBox MCP Server is a simple read-only Model Context Protocol server for NetBox. Prior to version 1.2.1, when running with TRANSPORT=http, the MCP server has no authentication on the HTTP endpoint. Any client that can reach the port gets a valid MCP session and full access to all four NetBox tools - no token or credential needed. This issue has been patched in version 1.2.1.10hCVE-2026-114357——
———Missing authentication for a critical function in the Android Debug Bridge daemon (adbd) in DJI CrystalSky ZS600C firmware v0.3.9.7 through v0.6.6.9 allows an attacker to obtain an unauthenticated shell (uid 2000), a foothold for privilege escalation to root. The device ships with ro.adb.secure=0 (no host key authorization) and USB ADB enabled by default; ADB over TCP is not enabled by default but, once enabled (e.g. via the shipped /system/bin/adbd_tcp.sh or 'setprop persist.adb.tcp.port 5555'), the same unauthenticated shell is reachable over the network (CVSS 4.0 base 9.3).14hCVE-2026-571467.5 ALT—
———PraisonAI is a multi-agent teams system. From version 4.5.115 to before version 4.6.61, the published A2U advisory GHSA-f292-66h9-fpmf says unauthenticated A2U event streaming was fixed in praisonai 4.5.115. Current head still exposes the same A2U subscription and event routes without authentication when the operator starts the documented CLI entrypoint. The current CLI wrapper does not expose --api-key, does not install the common API-key middleware, and does not generate a token for A2U. It calls create_a2u_routes(app) directly. That helper only enforces auth if A2U_AUTH_TOKEN is already present; if the variable is missing, _authenticate_request() returns None and treats auth as disabled. This issue has been patched in version 4.6.61.17h